Netgear WNDAP380Rv2 Manual do Utilizador Página 88
- Página / 152
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Advanced Configuration
88
ProSAFE Dual Band Wireless-N Access Point with RFID Support, WNDAP380R
Configure Wireless Bridging
The wireless access point supports a wireless distributing system (WDS) that lets you build
large bridged wireless networks. You can select from the following wireless access point
modes:
• Wireless point-to-point bridge. In this mode, the wireless access point can
communicate with another access point that also functions in bridge mode.
You can use
this mode with or without client association. Whether or not you enable client association,
use WEP, WPA-PSK, or WPA2-PSK to secure the communication. For information about
how to configure this mode, see Configure a Point-to-Point Wireless Network on page 88.
• Wireless point-to-multipoint bridge. In this mode, the wireless access point is the
master for a group of up to four access points that function in bridge-mode.
You can use
point-to-multipoint bridge mode with or without client association.
The other access points in the group need to be set to point-to-point bridge mode, using
the MAC address of the master wireless access point. Rather than communicating
directly with each other, all other bridge-mode access points send their traf
fic to the
master wireless access point. Whether or not you enable client association, use WEP,
WPA-PSK, or WPA2-PSK to secure the communication. For information about how to
configure this mode, see Configure a Point-to-Multipoint Wireless Network on page 93.
• Repeating the wireless signal. In this mode, this wireless access point repeats the
wireless signal, does not support communication with wireless clients, and sends all
traf
fic to a remote access point. In this mode, wireless clients cannot associate with the
wireless access point. Use WEP
, WPA-PSK, or WPA2-PSK to secure the communication
with the remote access point. For information about how to configure this mode, see
Configure the Wireless Access Point to Repeat the Wireless Signal Using
Point-to-Multipoint Bridge Mode on page 98.
For you to set up a wireless network in a WDS,
the following conditions need to be met for all
access points:
• All access points need to use the same SSID, wireless channel, and encryption mode.
• All access points need to be on the same LAN IP subnet. That is, all the access point LAN
IP addresses are in the same network.
• All LAN devices (wired and wireless computers) need to be configured to operate in the
same LAN network address range as the access points.
• The channel selection on the access points cannot be
Auto (see Configure the Basic
Wireless Settings on page 24).
Configure a Point-to-Point Wireless Network
In point-to-point bridge mode, the wireless access point communicates with another
bridge-mode wireless station. Use wireless security to protect this communication. The
following figure shows an example in which two wireless access points (APs) function in
point-to-point bridge mode with client association:
- ProSAFE Dual Band Wireless-N 1
- WNDAP380R 1
- Trademarks 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Monitoring 4
- Chapter 7 Troubleshooting 5
- What Is in the Box? 7
- System Requirements 8
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Introduction 13
- Installation and Basic 14
- Configuration 14
- Ethernet Cabling Requirements 16
- Web Management Interface 19
- To configure time settings: 20
- Configure the IP Settings 21
- Ceiling Installation 31
- Wall Installation 35
- Desk Installation 38
- Wireless Configuration and 39
- Security 39
- Security Profiles 42
- Security Profile Concepts 43
- Form for 802.11b/bg/ng Modes 44
- Form for 802.11a/an Modes 45
- Configure Legacy 802.1X 52
- Figure 11. Legacy 802.1X 53
- Figure 12. WPA with RADIUS 53
- Figure 13. WPA2 with RADIUS 53
- Figure 15. WPA-PSK 54
- Figure 16. WPA2-PSK 54
- Management 63
- Enable Remote Management 64
- Web Browser Upgrade Procedure 67
- TFTP Server Upgrade Procedure 68
- Defaults 69
- Restore the Configuration 70
- Settings 70
- Default Configuration 72
- Enable the Syslog Server 73
- To enable a syslog server: 74
- To configure STP and VLANs: 80
- Configure Hotspot Settings 81
- To set up a hotspot server: 82
- To configure advanced QoS: 86
- 4. Click Apply 87
- Configure Wireless Bridging 88
- Advanced Configuration 100
- Configure RFID Settings 103
- To reboot the RFID module: 106
- To reset the RFID module: 106
- 3. Click Apply 107
- Monitoring 108
- View System Information 109
- Monitor Wireless Clients 111
- View the Activity Log 113
- Traffic Statistics 114
- Troubleshooting 116
- Basic Functioning 117
- Wireless-Capable Computer 118
- Check these items: 119
- Request timed out 121
- Problems with Date and Time 122
- Troubleshoot the RFID Module 122
- Supplemental Information 124
- Technical Specifications 125
- Factory Default Settings 127
- Command-Line Reference 131
- Numerics 147
Manuais e produtos relacionados com Pontos de acesso WLAN Netgear WNDAP380Rv2
(28 páginas)
(43 páginas)
Pontos de acesso WLAN Netgear WG102 Manual do Utilizador
(110 páginas)
(110 páginas)
Acura 2013 MDX - Advanced Technology Guide (Base) manuels
Manuels d'utilisation et guides de l'utilisateur pour Voitures Acura 2013 MDX - Advanced Technology Guide (Base).
Nous fournissons des manuels en pdf 1 Acura 2013 MDX - Advanced Technology Guide (Base) à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais