Netgear WNAP320 Guia do Utilizador Página 67
- Página / 126
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 4. Management | 67
ProSafe Wireless-N Access Point WNAP320 Reference Manual
The following table explains the fields of the System screen:
Table 17. System Screen Fields
Field Description
Access Point Information
Access Point Name The NetBIOS name. For information about how to change the default name, see
Configure Basic General System Settings and Time Settings on page 19.
Ethernet MAC Address The MAC address of the wireless access point’s Ethernet port.
Wireless MAC Address The MAC address of the wireless access point’
s wireless card.
Country/Region The country or region for which the wireless
access point is licensed for use. For
information about how to change the country or region, see Configure Basic
General System Settings and Time Settings on page 19.
Note: It might not be legal to operate this wireless access point in a country or
regio
n other than one of those identified in this field.
Firmware Version The version of the firmware that is currently installed.
Current Time The current time. For information about how to change the time settings, see
Configure Basic General System Settings and Time Settings on page 19.
Current IP Settings
For information about how to change any of these IP settings, see Configure IP Settings and Optional DHCP
Server Settings on page 21.
IP Address The IP address of the wireless access point.
Subnet Mask The subnet mask for the wireless access point.
Default Gateway The default gateway for the wireless acces
s point communication.
DHCP Client Enabled indicates that the current IP address was obtained from a DHCP server
on your LAN network. Disabled indicates a static IP configuration.
Current Wireless Settings for 802.11n/g
Access Point Mode The operating mode of the wireless access point. One of the following modes is
ind
icated:
• Access Point
• Point-to-Point Bridge
• Point-to-Point Bridge with Access Point
• Multi-Point Bridge with/witho
ut client association
For information about how to change the mode, see Configure Wireless Bridging
on page 84.
Channel / Frequency The channel the wireless port is using. 11 is the defau
lt channel when the setting
is Auto. For information about how to change the channel and frequency, see
Configure Basic Wireless Settings on page 23.
Rogue AP Detection Enabled indicates that rogue AP detection is ena
bled; Disabled indicates that it is
not.
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Troubleshooting 4
- Contents 5
- Introduction 6
- What Is In the Box? 7
- System Requirements 7
- Key Features and Standards 7
- Key Features 8
- Hardware Description 10
- Top Panel 11
- Rear Panel 12
- Figure 3 13
- Ethernet Cabling Requirements 15
- Figure 4 17
- Web Management Interface 18
- Figure 7 19
- Figure 8 19
- Figure 9 20
- To configure the IP settings: 21
- 1. Select Con 21
- Figure 11 22
- Table 5. LAN Settings 23
- Figure 12 24
- Ceiling Installation 28
- 5. Conn 29
- Wall Installation 30
- 4. Conn 31
- Desk Installation 33
- Figure 13 35
- Security Profiles 36
- Figure 14 39
- Figure 15 40
- Figure 16 44
- Figure 17 44
- Configure Legacy 802.1X 45
- Figure 20 46
- Figure 21 46
- • WPA-PSK 47
- • WPA2-PSK 47
- • WPA-PSK & WPA2-PSK 47
- Figure 25 48
- 3. Click App 49
- Figure 26 50
- Schedule the Wireless Radio 52
- Figure 28 53
- Management 55
- SNMP Management 56
- Figure 30 57
- Figure 31 57
- Web Browser Upgrade Procedure 59
- TFTP Server Upgrade Procedure 59
- Defaults 60
- Restore the Configuration 61
- Settings 62
- Default Configuration 63
- Figure 37 64
- Figure 38 64
- Enable the Syslog Server 65
- View System Information 66
- Monitor Wireless Stations 68
- Figure 42 69
- View the Activity Log 70
- Traffic Statistics 71
- Figure 45 73
- Figure 46 74
- Field Description 75
- Advanced Configuration 76
- Figure 47 77
- Hotspot Settings 78
- Figure 49 79
- Figure 50 82
- Table 24. EDCA Settings 83
- Configure Wireless Bridging 84
- Figure 51 85
- Figure 52 86
- Figure 53 86
- Figure 54 88
- Figure 55 89
- Figure 56 89
- Figure 57 92
- Figure 58 93
- Figure 59 93
- Figure 60 96
- Troubleshooting 97
- Basic Functioning 98
- Wireless-Capable Computer 99
- Problems with Date and Time 103
- Use the Packet Capture Tool 103
- Supplemental Information 105
- Technical Specifications 106
- Factory Default Settings 107
- Command-Line Reference 109
- Notification of Compliance 117
- FCC Caution 118
- Industry Canada statement: 118
- Radiation Exposure Statement: 118
- Interference Reduction Table 120
- Numerics 121
- 122 122
- Index 123
- 124 124
- Index 125
- 126 126
Manuais e produtos relacionados com Pontos de acesso WLAN Netgear WNAP320
(70 páginas)
Pontos de acesso WLAN Netgear WG602v2 Guia do Utilizador
(122 páginas)
(122 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais